The DIR-320 model from D-Link is a fairly popular device for creating home wireless network. This router is often recommended by store consultants as one of the most reliable and at the same time inexpensive. In addition, the DIR-320 is used by many providers as a standard router installed by clients when connecting to Internet services.

Typically, the router parameters are adjusted by a specialist invited to install the provider’s cable into the premises. However, there are situations when you have to do it yourself. To ensure that creating a connection does not become an insoluble problem, you need to know how to configure a d link dir 320 router.

Installing the router and preparing the system

The router is connected in the standard way. On the back of the router case you can find a number of connectors, among which we are interested in the WAN and LAN ports.

The WAN connector must be equipped with a cable supplied to the premises by the provider; The router is connected to the computer via the LAN connector using the included patch cord.

Preparing the system involves checking the parameters network card and connection properties by local network:

WAN setup

To create a connection to the Internet, you need to get into the router interface. It is available at 192.168.0.1. (authorization pair – admin/admin).

The interface looks standard for D-Link routers with installed latest version firmware:
If you set up the D-Link DIR-615 router or other models of budget home routers from D-Link, you should have already understood all the available sections of the interface. If this is your first experience creating an Internet connection, then you will quickly learn to navigate here.

PPPoE connection

In the “Network” section, open the “WAN” item to open a list of available Internet connections.

If you already have a connection, do not delete it immediately. First and create a new connection. After setting up a new connection and saving the configuration, you can delete the old connection.

Leave the remaining parameters unchanged. Click the "Save" button to return to the list of connections. A light should light up in the notification menu at the top - click on it to update the hardware configuration.

L2TP connection

If you configured the upvel ur 315bn router to connect to Beeline, you probably encountered the need to specify the VPN server address. By the way, this is the only difference between setting up L2TP and PPPoE. Otherwise the procedures are completely identical.

Creating a Wireless Network

Users who have encountered the need to configure the ASUS RT-G32 Wi-Fi router or any other router know very well what parameters need to be specified to create a wireless network at home.

When setting up D-Link DIR 320, nothing changes in this sense:

Now you can close the router interface and try to search for the created access point from any device that has a Wi-Fi module.

You can connect the DIR-320 router to the Internet using external modem or a regular Internet cable provided by your provider. All parameters are specified in the web interface; no installation is required to configure the router separate application. D-Link devices have a large number of settings that allow you to achieve optimal performance home network.

Connecting the DIR-320 router and logging into the web interface

You can configure the router with a wired or Wi-Fi connection. Insert into the router the Internet cable that was installed into the premises by your provider. To do this, use the last port, indicated in gray. Connect your home computers using the LAN ports highlighted in blue on the back panel.

Insert the power supply plug into the “5V-2A” connector. If the Internet is connected via an external 2G/3G modem, insert it into the “USB” connector. Plug the DIR-320 into a power outlet only after connecting all cables and external devices. Otherwise, the router may malfunction or be damaged.

Connect the network on the computer from which you will change the parameters of the D-Link DIR-320 router. At using Wi-Fi select "D-Link" from the list of wireless connections. By default, there is no encryption, so you can complete the operation without entering a password. If you are using a cable connection, insert the plug into the Ethernet port of your computer or laptop.

On your chosen device, open a web browser, such as Google Chrome. In the address bar of the program, enter the IP through which you will access the settings of the DIR-320 router. The address in the router's standard firmware is: 192.168.0.1. On the page that opens, you will need to enter data to access the control panel. Standard login and password: “admin”. Fill out the text fields and click “Login.”

Pay attention! If the account on the D-Link DIR-320 was changed earlier, reset the router settings. To do this, press and hold the “Reset” button on the rear panel for 10 seconds. When the factory settings are restored, log in again using the default data.

If you enter your account information correctly, you will be redirected to the statistics page. Among other data, it displays the total number RAM on the DIR-320 router and the amount of available memory. Below is the time since the D-Link router was last turned on.

Internet connection via 2G/3G modem

To establish a connection via external device, go to the “Internet Settings” menu and in the first field mark the value “ USB Adapter" Select your carrier name from the following drop-down list. If the system does not have data for your 2G or 3G provider, set the value to " " and write the operator's name in the next text box.

In the “Username” and “Password” sections, enter the information provided by your provider. If necessary, enter the dial-up number in the appropriate field and the name of the access point in the “APN” line. You can find out the information you need in technical support or on the official website of the Internet provider. It is recommended to leave the remaining points unchanged.

Open the “USB modem -> Information” section. In the first list, specify the modem type depending on the wireless generation you are using. Allow access to mobile Internet in the second drop-down list. The remaining rows of the table will contain information about the connected device. Click the "Connect" button in the lower right corner of the page.

Important! If the modem is not recognized, unplug it, then plug it back into the USB port and click the "Update" button below the table.

Some operators require you to enter a PIN code to connect to the mobile Internet. You can specify this information in the same menu, through the “PIN” section. Enter the current digital password provided by your operator in the PIN field. To prevent the system from prompting you for a code each time you connect, check the box and click “Apply.”

Cable connection of DIR-320 to the Internet

Open the Network menu and go to the tab P-t-p interfaces" By default, their list will be empty. To create new interface for D-Link, click the "Add" link in the connection table. In this section, you can create a network connection using the L2TP, PPTP and PPPoE protocols.

Select the connection type from the first list. It can be specified in the agreement concluded with the Internet provider. The data is also indicated there account, if they are required to establish a connection. If there is no contract, you can clarify the data by calling or writing to the support of the company that provides Internet connection services. Fill in the required fields and click “Edit”.

Connecting with a static IP is done in a similar way. When you select “Static” in the “Interface Type” section, new text fields appear: IP address, network mask, MAC address. All this data is also provided by the provider.

The “Status -> Network Statistics” section contains information about the operation of different interfaces, including:

• Assigned addresses;
• Reception and return speed;
• Number of received and sent packets;
• Dropped packets;
• Packets received with errors.

Setting network parameters

You can manage running interfaces in the “Network -> Network Interfaces” section. The current connection status is displayed next to each entry. Each of them can be temporarily stopped or disabled. Available interfaces include connected LAN devices (laptops, computers and other home network devices), wireless technologies Wi-Fi and WiMAX.

To add DNS servers, go to the “Name Servers” section. The default “Configuration method” field is set to automatically receive values ​​from the Internet provider. Selecting “Manual” will allow you to specify other DNS servers. You will be able to enter their IP addresses in the second text box. To save addresses, click “Edit”.

The assignment of IP addresses within the local network is performed by the DHCP server. Open the “DHCP Settings” tab to change its operating mode. In the “Static DHCP” table you can bind permanent addresses for individual devices. The match is determined by the MAC address.

You can find out the MAC address of the device for further binding in its settings. For computers under operating system control Windows systems MAC determination is made in command line. To do this, use the command: “ipconfig /all”.

The settings of the current server can be changed by clicking on its name. Most important parameters in this table - the starting and ending addresses of the range. The system will automatically assign IP addresses from this numerical range to new clients. If you need to change it, make sure that the new values ​​are within the range allocated for local networks.

Training video: Step-by-step setup of D-link DIR-320 for dummies

Wi-Fi setup

Open the “Network -> Wireless connection" The first checkbox is responsible for the operation of the Wi-Fi module. If you remove it, the router's wireless broadcasting will be stopped. Other options:

• Hide access point—makes the network invisible in the general list.
• SSID is the Wi-Fi name that will be displayed when searching for networks.
• Country—allows you to select the territory in which the device is used. The parameter affects the list of allowed channels.
• Channel—band number within the Wi-Fi frequency. Standard value: 6.
• To select the encryption type and specify the Wi-Fi access key, click “Security Settings.”

In the first list, select the network authentication method. By default, the connection to D-Link is unencrypted and no password is required to connect to Wi-Fi. It is recommended not to leave the value “Open” to avoid interception of network traffic. Select a different authentication type and set a PSK key (the password that will be used for Wi-Fi).

Important video: D LINK dir 320 router settings

Changing router system parameters

On the “System” tab, you can reboot the D-Link router or go to any subsection. If a reboot is performed by clicking a button in the Actions table, the changes made in the previous steps will not be applied. To save them, use another button: “Save and reload”. It is located in the upper right corner.

The “Administrator Password” section allows you to change the standard account information. To do this, select the “admin” user and check the “Change system password” checkbox. Enter New Password and its confirmation in the next two text fields. To ensure the best security for your home network, use complex passwords that contain special characters, numbers, small letters, and capital letters.

When all the necessary settings Wi-Fi router D-Link DIR-320 will be changed, it is recommended to save the configuration to a file. Go to the menu item “System -> Configuration”, click “ Backup" and select the directory in which the backup will be written. If the router malfunctions or another user accidentally restores the factory configuration, you can return the settings from the saved file.

Advice! To restore factory settings, use the corresponding item in the same menu.

D-Link recommends updating your router software regularly. Each new firmware contains not only expanded functionality, but also network security updates. Using the latest version of the software will protect your device from hacker attacks. The current version can be downloaded from the manufacturer’s website, in the “Support -> FTP” section.

The downloaded file is installed on the DIR-320 through the “System -> Software Update” menu. Click the “Browse” button and specify the path in the system where the new firmware is saved. Then click "Update" in the lower right corner. The update installation process will take several minutes. After the router automatically reboots, you will be able to use the new version of the software.

D-Link routers are very popular among users. Therefore, instructions for setting up, setting a password, solving some problems, etc. are always relevant. In this article, we will set a password for Wi-Fi on a D-Link router. I will show the whole process using the example of the D-link DIR-615 router model, which we configured in the article. In the instructions for setting up certain models, I always try to write about setting a password for the wireless network. But a general article for all D-Link models would not hurt.

Using these instructions, you can set a password on D-link DIR-300, DIR-615, DIR-320 and other models. Is that there? different versions firmware that differ in interface. Therefore, let's consider several options.

Regarding the issue of installing protection on Wi-Fi network, That It is necessary to set a password. And preferably during the first setup. Believe me, there are many people who want to connect. And this is an extra load on the router, low connection speed, and it’s not safe. It may even be that by connecting to your network, a third party will gain access to your files. Now, if you don’t have a password right now, you can take a look. If your network has been open for a long time, then I am sure that you will see not only your devices there.

Therefore, I advise you to come up with good password, be sure to remember it (or write it down) and protect your home network.

Instructions for setting a password for the Wi-Fi network of a D-Link router

In fact, nothing is difficult. First, go to the router settings. It is advisable to connect to the router via cable. But, if this is not possible, then you can use Wi-Fi (if any problems arise after installation, see solutions at the end of this article).

In the settings go to the tab WiFi - Security Settings (if you have an English menu, then change it to Russian). In the drop down menu Network authentication install WPA2-PSK. In the field PSK encryption key enter the password that will be used to connect to your Wi-Fi network. Just come up with a more complex one than my “123456789” :) The password must be at least 8 characters long.

In the section "WPA encryption settings" We don’t change anything, we just press the button Apply.

If your control panel is different from the one I have in the screenshot above, then you can try.

If you don't want to update the software, here's another one: instructions for installing protection on D-link with older firmware (light interface) :

In settings go to the tab Configure manually.

Then, open the tab WiFi And Security Settings.

Set a password, save the settings, and reboot the router.

And more instructions for firmware with a dark interface:

Save the settings and reboot the router.

What should I do if I can’t connect to Wi-Fi after setting a password?

A very popular problem is when, after setting a password for Wi-Fi, computers, phones, tablets, and other devices do not connect to the wireless network. On a computer, this is usually a well-known error. "The network settings saved on this computer do not meet the requirements of this network", or "Windows was unable to connect to...". Mobile devices may simply not connect.

What needs to be done. You just need to delete the Wi-Fi network on your computer, forget it, and reconnect with the password that you set in the router settings. It's very easy to do. I wrote about this in detail in this article:. If you have Windows 10, then see the instructions.

On mobile devices you just need to click on the network, hold it for a while, and select Delete from the menu.

In this article we will look at the topic of how to configure the d link dir 320 router. The dir 320 router is in third place in popularity among the routers of the Dlink company, so it is often recommended in stores. Many people have questions about setting up this model. In this article we will go through detailed instructions for setting up a wifi router d link dir 320. We will look at all types of Internet connections using the Beeline provider as an example. Most importantly, before doing anything with the router, read the instructions to the end.

Setting up a network card on Windows 7 and XP

Before you start setting up any router, you need to configure the network card on your computer; this also applies to the d link dir 320 router. In the Dlink router, at the factory settings, the IP address is distributed automatically by default. Therefore, we need to set the IP address to be obtained automatically in our network driver.

Setting the IP address automatically on Windows XP

Go to “Start” and find “Control Panel”. After going to the “control panel” Find the “Network Connections” icon, click on it and in the next window, right-click on the “Local Area Connection” icon and select “Properties” from the list. In the window that appears, in the list with checkmarks, select “Internet Protocol (TCP/IP)” and click on the properties button. Then we check whether the points are set in the points where words are present automatically; if not, then set them and press the “OK” button. See pic below.

Setting the IP address automatically on Windows 7

We go to Start, in the search bar (which is located at the very bottom of the Start window) we type the word “Network”. From the list of results, select “View network connections" Then in the window that opens, double-click on the “Local Area Connection” icon. Find the “Properties” button and click on it. Now, in the list with checkmarks, find “Internet Protocol Version 4” and double-click on it. Now we put dots in the points where the words are indicated automatically and click “OK”. see fig. below.

Solving problems when connecting the router d link dir 320

After setting up the network card, you need to check whether you have received the correct IP address. To do this, you need to return to “Local Area Connection”, double-click on it and select the item in the window that opens:

• On Windows XP – There will be a “Details” section at the top of the window
• On Windows 7 – Somewhere in the middle there will be a “Details…” button

There you will see the IP address, it should look something like this 192.168.0.xxx, where xxx is any number, for example: 101 or 3. If problems arise, the IP address will be 169.xxx.xxx.xxx. I won’t go into details about why this happened, I’ll explain how to solve the problem. You need to specify the correct IP addresses in the network card settings. We will need to return to point:

• On Windows XP – Properties: Internet Protocol (TCP/IP)
• On Windows 7 – Properties: Internet Protocol Version 4 (TCP/IPv4)

And specify the following settings:

• IP - 192.168.0.101
• Subnet mask - 255.255.255.0
• Default gateway - 192.168.0.1
• DNS - 192.168.0.1

Then click “OK” and the router should connect to your network card.

Replacing the old firmware d link dir 320 with the current one

After connecting the router to the computer, you should update the firmware to the latest one so that there are no problems with connecting to the Internet and WiFi in the future. This will also allow you to learn how to do this right away, so that in the future you can easily change the firmware of the d link dir 320 router, and for other models of the Dlink family. First, you will need to download the latest firmware. At http://ftp.dlink.ru/pub/Router/DIR-320_NRU/Firmware/ (for DIR-320NRU) and http://ftp.dlink.ru/pub/Router/DIR-320/ (for DIR -320) there will be a file with the latest version of the router firmware dir 320.

Download it to your computer before you disconnect from the Internet to set up your router.

Login to router Dlink dir 320

For any firmware there is a standard input to the router configuration interface. Having opened any browser, type 192.168.0.1 in the address bar, after pressing “Enter” you will be asked for authorization. You will need to enter your login (Username) and password. There are only two options

1. For the very first firmware of the router, the Login will be admin, and the Password line will be left empty.
2. For newer firmware Login and password, admin and admin.

If your router was purchased a long time ago, then you have one of the first firmware 1.0.1. She looks like see fig. below.

As you can understand from the figure, after entering the router settings, go to the “Maintenance” tab, and then to the menu section on the left “firmware update”, click the “Browse” button and select the file with the new firmware. Once selected, click the “apply” button, then wait for installation.

Let's deal with newer firmware at once:

1. If your firmware looks similar to the first option in the figure, select “System” in the menu on the left, then “Software Update”, then click “review” and select new firmware.
2. In the second option, first click on “Configure manually”, then also select “System” - “Software update”. Select new firmware and install.
3. And the last third option. Click “Advanced settings”. Then in the “System” block, click on the forward button and select “Software Update”.

I want to immediately warn you that after you click on the “Update” button, the browser may freeze and you will get the impression that you did something wrong. Do not do anything for 4-7 minutes. Then enter the router address (192.168.0.1) into the browser again.

After installing the new “software”, you can move on to the most important thing - setting up the Internet and wifi on the router.

Internet settings of the router d link dir 320

Setting up the Internet in new versions The firmware is quite simple and does not differ from other models of the Dlink company. Therefore, I advise you to consider the basic setup of connection types such as “PPPoE”, “Dynamic IP”, “Static IP” for those who need setup for Rostelecom. In this article I will talk about setting up a connection with the Beeline provider.

Setting up a router d link dir 320 beeline

If you read the article I suggested above, you know where you need to go to set up the Internet. If not, then I will briefly describe:

1. After entering the setup interface, select “Advanced settings”.
2. Then in the “Network” column - WAN. And click the “Add” button
3. Afterwards we make the following settings

To work with the Beeline provider, in the Connection Type, select L2TP + Dynamic IP, this is the most important thing. In the Connection name field, you can enter whatever you want, for example, mybeeline. The Username and Password fields are also very important; here you need to enter the data that the installers provided to you when connecting (if you lost them, check with technical support). Beeline VPN server address tp.internet.beeline.ru. After entering the data, click on the Save button. Then at the top you will also see a Save button, click on it. Setting up the d link dir 320 router for Beeline is complete and if you entered all the settings correctly, the Internet should already be working. For clarity, see the figure below.

Setting up Wi Fi dir 320

After setting up the Internet, you should also configure the wifi network on the router. In order to do this, we need to return to the “advanced settings” and in the “WIFI” block select “ General settings" Here we are only interested in the “SSID” setting - this is the network name, i.e. the name that will be visible in the list wireless connections. Choose a name that you like and click change.

It’s also worth setting up security so that noxious neighbors don’t play around. In the same block, click on the “Security Settings” link. Now we are interested in two points:

1. “Network authentication:” - be sure to select “WPA-PSK2”. Then you can be sure of the security of your network.
2. “PSK encryption key” is the password for connecting to your network. You must enter at least 8 characters.

After entering all the data, click “Change”.

That's it, the router setup is complete. But this is not all the capabilities of this router. Various articles indicate all the possible capabilities of this router. To find them, enter “320” in the search bar at the top and you will get all the articles that talk about the router dir 320.

I recommend watching the Video: Setting up D-link DIR-320
.

Buying a new configured router is not a problem for a domestic user, but there is often a need to make some adjustments to the parameters for yourself. This is where the problems begin, because the operating instructions contain only data on setting global parameters of network equipment for smooth operation on the Internet.

The focus of this article is setting up the DIR-320. Step by step guide will not only help the user quickly master the control panel of the router, but also introduce him to all the functionality of the network device, which is not advertised in the specifications upon purchase.

First step in setup

Many owners computer equipment encounter problems when independently connecting the router to a personal computer or laptop. The problem lies in the settings - the computer and the network device operate on different networks. The first step that the owner of the DIR-320 router must take is to reset the settings. The procedure is simple. There is a Reset button on the back of the device. You need to connect the router to the electrical network, wait until the device boots up (15-20 seconds) and hold the reset button with a sharp object (a needle or toothpick) for several seconds. The reboot signal will be indicated by the indication on the router - all the lights will blink simultaneously.

Connecting to a computer

The DIR-320 begins with a connection to a workstation. Using the Patchcord cable included in the kit, you need to connect the router to a personal computer or laptop. There are 5 ports on the network equipment, one of which is for (WAN). The remaining ports are needed to build a local network. It is in one of them that you need to connect the Patchcord cable.

The DIR-320 router is configured in such a way that when it is connected to the Internet, the device automatically gains unhindered access to the global global network. Accordingly, the router's four LAN ports allow the user to connect to the Internet. In fact, the owner of the network device does not need to configure anything. The main thing is to connect the network cables correctly.

Preparing the Workstation

Most users' personal computers have automatic settings on the network, but there are exceptions. Therefore, we have to get acquainted with force majeure. Setting up the DIR-320 router is possible only in cases where the network equipment and personal computer are on the same local network. The default is 192.168.0.1 - 192.168.0.254. The router takes the first value and automatically assigns addresses to all devices connected to it. Accordingly, the computer must automatically receive an address from the network equipment, otherwise setting up the DIR-320 will be impossible.

By going to the “Network Control Panel”, the user needs to go to “Change adapter settings”. Having found the desired connection, click on it with an alternative mouse button and select “Properties”. In the menu that appears, place the cursor on the “IP version 4” field and click the “Properties” button. Then in the menu that opens, set the “Receive automatically” option in two computer settings fields and save.

Downloading the Control Panel

The DIR-320 router is controlled via a Web interface, so the user needs to open any browser and enter “192.168.0.1”. At correct connection router to the computer, after a short delay, an invitation for the network equipment to enter the control panel will appear on the monitor screen, asking for a login and password.

The login information is located on a sticker that can be found on the bottom of the router. Often the default login and password are identical - “admin”. Enter without quotes, in capital Latin letters in both request fields.

Safety comes first!

For the D-Link DIR-320 router, setting up the equipment begins with updating the software from the manufacturer's official website. To do this, you need to follow the link provided in the user manual and download the current firmware version. Alternatively, software for the router, you can also download it from the provider’s website. After all, the Internet service provider is interested in ensuring that its client has secure firmware. Often, the provider provides users with ready-made firmware with network settings. Naturally, you need to download it before connecting the router to your computer.

The DIR-320 is easy to flash. You need to go to the “tab” in the control panel Maintenance(Maintenance)" and select "Firmware Update". It will open and prompt you to specify the path to the file on personal computer. After clicking the “Ok” button, the download will begin. At the end of the firmware procedure, the equipment will reboot automatically.

Do everything quickly

The DIR-320 can be configured as in manual mode, and in automatic. At least that's what the manufacturer claims. In fact, everything additional settings are made by hand. Automatic mode(with an assistant) only provides the user with the correct sequence of menu items for the convenience of entering the necessary parameters. If you need to set up an Internet connection, the assistant prompts you to enter the necessary data for a correct connection. Otherwise, the control panel provides access to wireless interfaces.

In the DIR-320 router, setting up WiFi is simple - you need to specify the name of the access point (the name of the detected network) and set a password. All other parameters are set automatically. In manual mode, the user will have to independently set a dozen parameters. Many users believe that manual configuration is more interesting in terms of learning how to work with a network device, but it is many times more difficult than automatic input.

Working with a modem

In the DIR-320 router, 3G configuration is carried out only in manual mode. Before making changes, owners should read the operating instructions, which describe in detail the operation of the device with several providers simultaneously. The fact is that by inept actions the owner can disrupt the operation of the wired connection.

On the control panel, you need to select the first item “Internet Settings” and go to the “Settings” section. In the window that appears, click the “Manual settings” button located at the very bottom. In the next window, the user's choice must be made in favor of “PPP connection via USB”. Since D-Link DIR-320 is not specifically tied to 3G (even a regular GPRS phone can be connected), the user only has to fill in the required fields. For a 3G connection, indicate: login, password and dial-up number. For the phone, you need to additionally register the operator’s server and specify the command for dialing.

Fine-tuning the local network

Also interesting in the D-Link DIR-320 router is setting up a demilitarized zone. A network hidden from prying eyes can combine all the electronics in the house, providing access to it over the network to only one owner. If we talk about security, the DMZ menu item is required for detailed study by the user.

Fans of online games will have to become familiar with port forwarding, because very often providers close unused ports. This is done to protect your own network, but many people forget about gamers. With DIR-320, everything is simple: the protocol is indicated, then the replaced ports are written opposite each other.

In conclusion

This is not to say that setting up a router on your own will be easy. Network equipment requires a lot of attention and certain knowledge. Any parameter specified incorrectly will cause the router to malfunction and, accordingly, block the user’s access to the Internet. But any problem can be solved: the router can always be returned to factory settings and started all over again.

And yet, experts in the field of IT technology recommend that owners of network devices read the operating instructions - simply scrolling through will not be enough. You need to read the entire manual. Only after studying the basic parameters and correctly filling out all fields on the device control panel can setting up the DIR-320 bring results.